Home / Guides / Measuring
BUYER GUIDE · MEASUREMENT

How to Measure for a Men's Hair System

Most custom hair system returns trace back to a wrong measurement, and almost always the same wrong measurement: head circumference. What the factory needs is the size of the area being covered, edge to edge, plus the depth at the nape. This guide covers the four dimensions, how to take them, and how to record them so a reorder repeats exactly.

Last reviewed November 2026 · measurements in inches unless stated

A hair system is sized to the bald or thinning area, not to the head. A hat size tells the factory how big the skull is; it says nothing about where the piece has to sit or how far the temples need to reach. Ordering to head circumference produces a piece that is too large at the corners and lifts within a day of fitting.

The four dimensions

DimensionHow to take itWhy it matters
Front to backFrom the front hairline to the nape edge, over the crownSets the length of the piece
Width acrossEdge to edge at the widest point, usually above the earsSets the temple fit
Nape depthFrom the back edge up to where coverage stopsPrevents the piece lifting at the neck
Temple curveFollow the natural hairline shape, not a straight lineA straight front on a curved hairline reads as a wig

Tape-and-trace is more reliable than a tape measure

Place clear film or paper over the area to be covered, mark the boundary with a marker pen, then measure the marked shape. The traced outline can be sent with the order and the factory builds to the outline rather than to two numbers. This catches the temple curve and any asymmetry, both of which a pair of measurements flattens away.

If a trace is not possible, measure across the widest point in both directions and add the nape depth, and record whether the wearer's existing piece was too tight or too loose at any point. That note is more useful than a millimetre of precision.

Take the measurement on the wearer, not from an old piece

An existing piece has usually stretched. Measuring it gives the buyer the dimensions of a worn-out product rather than the dimensions of the head. If the old piece is the only reference available, measure it but note that it has been in service and ask the wearer whether it felt correct at fitting.

Recording a specification that repeats

A specification that can be reordered without a new sampling cycle contains six fields. Recording them once removes the most common source of inconsistency between orders:

  • Cap shape: the traced outline or the four dimensions above.
  • Density: the percentage ordered, not a word like 'medium'.
  • Hair length and curl: length in inches, and the curl category.
  • Colour: matched to a hair ring or a daylight photograph, with a reference number.
  • Grey percentage: the blended share, not a shade name.
  • Base construction and thickness: e.g. French lace with 1-inch PU perimeter, or PU 0.04 mm.

Sending colour information that actually matches

A photograph taken in daylight without a filter is the minimum. A hair ring is better. Colour names differ between suppliers and between production batches, so 'dark brown' means nothing without a physical or photographic reference. If the buyer's customers are grey, the grey percentage matters as much as the base colour, because grey blending is hand work and a 20% blend does not look like a 5% blend.

Sizing standards versus custom

Standard sizes — commonly 8×10, 7×9 and 6×8 inch — cover most wearers and let a buyer stock without a measurement round. Custom shapes are for non-standard coverage, unusual temple lines, and buyers selling into a studio where the retail price supports the lead time. Stocking three standard sizes and ordering custom only when the retail price justifies it is the usual balance.

The most expensive measurement error is not a millimetre; it is measuring a stretched old piece and calling it the specification. Always measure the head.

What to do when a piece arrives the wrong size

Check it against the confirmed specification sheet before fitting, not after. If the cap dimension is off, the discrepancy is a production issue and should be raised before the piece is worn — once it has been cut, trimmed or glued, it can no longer be assessed as delivered.

FAQ

Questions on this guide

Questions buyers ask before ordering. If yours is not covered, send it on WhatsApp and Ryan will answer it directly.

Can I just use a hat size?

No. Head circumference describes the skull, not the area the piece covers. A piece built to a hat size is usually too wide at the temples and lifts at the corners.

Do you need a physical template?

A traced outline is the most reliable, but four dimensions plus a note about fit problems are usually enough for a standard shape.

How often should a specification be re-measured?

Only when the wearer's coverage changes or a piece fits poorly. A recorded specification should repeat across reorders without re-measuring.

Let’s Talk Business

Need a Wholesale Catalogue or Quotation?

Send Ryan your preferred base, size, density, color and approximate quantity. We’ll reply with the most relevant products and wholesale details.

WA WA