Home / Guides / Sample Checklist
BUYER GUIDE · QUALITY CONTROL

What to Check in a Wholesale Hair System Sample

A sample order exists to answer questions, not to admire the product. Buyers who fit a sample once, in good light, and then place a bulk order are usually the buyers who end up with stock they cannot sell. This checklist is the seven things worth testing, in the order that eliminates problems fastest.

Last reviewed November 2026 · designed for first-order sample evaluation

Run the checks in this order. The first three eliminate most bad samples within an hour; the last four take a week but decide whether the piece survives real service. Skipping to the end and judging by how the hair feels is the most common mistake.

1. The hairline, in daylight, at conversational distance

Fit the piece and look at the front edge in daylight — not under a warm shop bulb, which hides knots. Step back a metre and look again. A knotless or V-loop front should show no dots at the edge. A bleached front should show no dark points. If the edge reads as a line, the construction is wrong for the customer it was ordered for.

2. Density against the intended customer

Compare the density you ordered with what arrived, and with what the customer's own hair looks like. A 130% piece on a wearer with fine, greying hair reads as a hairpiece regardless of how good the base is. Density mismatch is the fastest route to a return.

3. The base edge, before and after one removal

Apply the piece, wear it briefly, remove it, clean it and re-apply. The perimeter is where most failures begin. On lace, check whether the mesh edge has started to fray where the tape sat. On skin, check whether the edge has stretched or torn. A sample that fails on the second application will fail on the customer's tenth.

4. Colour under two different lights

Look at the piece in daylight and then in indoor light. A colour that matches under one and not the other will generate complaints, because customers see themselves in both. Check the grey blend specifically — a 10% grey blend that reads as a stripe rather than a scatter is a hand-work problem, not a colour problem.

5. Hair behaviour after washing

Wash the piece once with the products the buyer's customers actually use, dry it naturally, and look at how it sits. Human hair that has been over-processed loses its cuticle and mats at the ends; you will see this after one wash. This test also shows whether the colour shifts, which is the second most common complaint after density.

6. Construction against the order

Check the specification line by line: base type and thickness, front construction, cap dimension, density, hair length, curl, colour. Production errors are cheaper to catch on the sample than on a thirty-piece run. Where something differs, raise it before the bulk order rather than accepting it as close enough.

7. Packaging and handling

Check how the piece arrives. A piece that arrives creased or crushed tells the buyer something about how a production run will arrive. If the buyer intends to resell, the packaging format matters as much as the product, because the retail presentation is part of what the customer is paying for.

Seven checks, one week of wear, two light sources. That is the whole of a proper sample evaluation — and it costs less than a single discounted stock run.

What a good sample response looks like

A supplier that answers specification questions with production detail, corrects a discrepancy before a bulk run, and can explain why one construction behaved differently from another is a supplier worth building a range with. A supplier that answers only with reassurance is not.

Turning the sample into a range

Once a sample passes, the range is built by varying one variable at a time from the passing specification: a second density, a second colour, a longer hair length, or a second base. Changing several at once makes it impossible to tell which change caused the next problem, and it is how buyers end up with a catalogue they cannot explain.

FAQ

Questions on this guide

Questions buyers ask before ordering. If yours is not covered, send it on WhatsApp and Ryan will answer it directly.

How long should I test a sample?

Wear it for a week with at least two removals and clean-ups, and wash it once. A single fitting tells you about the hairline but nothing about durability.

What is the most common sample failure?

Density mismatch and perimeter wear after the second application. Both are visible within a week and both are fixable before a bulk order.

Should I test more than one construction?

Yes. Two samples of the same density across two base types, fitted on the same wearer, is the cheapest way to decide a market's preference.

Let’s Talk Business

Need a Wholesale Catalogue or Quotation?

Send Ryan your preferred base, size, density, color and approximate quantity. We’ll reply with the most relevant products and wholesale details.

WA WA